05.00.00 Technical science
-
APPLIANCES, TECHNOLOGIES AND EQUIPMENT FOR HAULING OF FRUIT OUT THE GARDEN
DescriptionAn integral part of technological process for the cultivation of agricultural crop is the transportation issues. For their execution, we require significant energy and labor costs. The statistics show that the proportion of expenses for transportation of goods in agriculture reaches 25-40% of the total costs for ready-to-sale production, when the proportion of farm tractor transportations reaches 60% of the total. Thus, there are considerable losses of production, reaching in separate cases up to 50%. They are especially great in the harvesting and post-harvest cycles of crop production which is connected with crop damage during transportation. Large losses of fruit and vegetable products when transporting might be connected with their mechanical damage level during loading, unloading and transportation. This causes the urgency of the problem of preservation when transporting fruit and vegetables. One of the prior national issues is "... the development of directions to improve road transport maintenance with the aim of improving the quality of the transport process, which includes increasing commercial speed of freight flows by 2-3 times, increase productivity and profitability of road transport systems by 2-3 times, reducing the environmental load on nature by 20% ... " and others mentioned in the "Transport Strategy of Russia until 2020"
-
ANALYSIS APPROACHES TO EVALUATION OF INFORMATION PROTECTION
DescriptionThe article is devoted to an actual problem of information systems’ security assessment and the importance of objective quantitative assessment results receiving. The author offers the creation of complex system of information security with system approach, which will be used at each stage of information system’s life cycle. On the basis of this approach the author formulates the general scheme of an information security assessment of information system, and also the principles of an assessment’s carrying out method choice. In this work the existing methods of a quantitative assessment based on object-oriented methods of the system analysis, and also the objectivity of the received estimates on the basis of this approach are considered. On the basis of the carried-out analysis, serious shortcomings of the used modern techniques of an information systems’ security assessment are allocated, then the idea of the scientific and methodical device providing the increase of objectivity and complexity of an information assessment means on the basis of expert data formalization creation necessity was formulated. The possibility of this approach application for expeditious receiving a quantitative information security assessment in the conditions security threat’s dynamics changes, functioning and developments of information system is considered. The problem definition of automated information systems’ security assessment is executed, and the general technique of protection means of information in systems of this type was formulated
-
STUDY OF POLYMERIC MATERIALS PERFORMANCE IN FRICTION CONDITIONS WITH ICE AND SNOW
DescriptionThe problem of identifying of the most promising polymer materials for sledge sliding application. The comparison of materials is given: the bench tests of polyethylene, fluoroplast, steel and ultra high molecular weight polyethylene (UHMWPE) with different molecular weight and their composites are carried out. On the basis of research of polymeric samples on ice and snow friction in exploiting condition with the use of specially designed sledges was shown that GUR 4150 UHMWPE has the lowest mass volume and linear wear. Also in article the results of research of ice adhesion to different materials are presented. Adhesion research was carried out in low temperature conditions of air from -21oC up to -46oC and in cryocamera according method which was patented by Institute of oil and gas problems of SB RAS. The research showed that GUR 4150 UHMWPE has the lowest adhesion to ice. On the basis of obtained data the authors assumed that GUR 4150 is the most perspective materials for development of sledge sliding exploiting in Arctic conditions.
-
Description
Based on the analysis of the phase composition, the average grain size measured by high resolution electron microscopy and multifractal parameterization structure shows the relationship of coating properties with their structural-phase state. The regularities of the evolution of the structural parameters and multifractal characteristics of the surface layers of materials with shape memory can predict the properties of the composition of the "steel-coating". On the basis of experimental studies, it has been shown that mechanical activation of powders of materials with shape memory effect based on TiNiTa makes it possible to create an effective technology training sprayed material which will generate nano-structured surface layers by high-speed flame spraying. The influence of the mechanical activation of TiNiTa powder on the quality of surface layers formed by high-speed flame spraying was investigated, and a significant improvement in the structure of the surface layer was found, with reduced porosity, high adhesion, and, consequently, increased functionality and mechanical properties. The evolution of the structure at all stages of surface modification based on the fractal approach multifractal parameterization method, which is based on qualitative analysis and instrumental methods in addition to classic microstructure parameters like grain size and specific area related to the physical and mechanical properties, is quantitative information. It was established experimentally that after high-speed flame spraying, the performance characteristics of mechanically activated shape memory TiNiTa powder improved: cyclic durability under high-cycle fatigue increased by about 35.6%, and the wear resistance increased by 3.6 times
-
MODULE HOUSE AS A PERSPECTIVE FOR FARMERS
DescriptionIn 2014 citizens of Russia felt the whole power of the introduction of reciprocal sanctions. Since 2014 the import of pork from the European Union has been limited and since August this has happened with poultry meat from EU and the USA. These actions led to the shortage of meat raw and rise of prices on meat produce in some regions of Russia. In spite of it, many business owners positively assess the possibility of full substitution of imported raw products. The government of the Russian Federation is ready to invest the projects for substitution of import products. In the conditions of crediting with credit rate of 25% the construction of small and average companies will be too heavy for rising. The construction of even small processing enterprise takes much time and powers. In connection with it, one of the perspective ways of the decision of this problem is the use of module houses of small and average power. Such houses allow processing meat and fish of small amounts. In comparison with capital construction the installation of a module house demands only specific areas, supply of electrical energy, water and withdrawal of sewage. There were considered the examples of module houses with the description of equipment and constructive peculiarities in the article. There were cited the advantages and the disadvantages of the offered module houses. There were formulated the recommendations on using already existing companies
-
Description
The most important physical properties that characterize the substance are density and saturated vapor pressure (SVP). These parameters are required for the development of new technical processes in the petroleum and chemical industries, design of pipelines, pumping and fuel equipment, etc. Existing methods for calculating of density near and on the saturation lines are imperfect, and finding of the analytic dependence of SVP of petroleum products from all defining parameters associated with great difficulties. The purpose of present work is an experimental research and development of methods for calculating the density (specific volume) near and on saturation lines, and saturated vapor pressure of gasoline straight-run fraction derived from petroleums from three fields: Mangyshlaksky, Trinity-Anastasevsky and West Siberian. The choice of objects for research is due to the necessity of creating methods for calculating of density and SVP of oils obtained from various hydrocarbon group composition petroleums. Area of state parameters in the present work by temperature (20 ÷ 320°C) and pressure (0,03 ÷ 30 MPa) provides the ability to research gasoline fractions to supercritical regions. Measurement of density and SVP of petroleum fractions performed with help of a specially created for this purpose experimental installation
-
Description
The article describes the methods of calibration and working measurements, planning of experiment and experimental data processing, characterized objects of study and provides illustrations of research results of P-t depending for petroleum fractions. We have described the results of generalization of density (specific volume) of the examined samples in the liquid and on the saturation line and SVP in the two-phase region. The article shows that existing methods of calculation based primarily on the results of the study of the density and SVP of individual hydrocarbons and extremely limited experimental data of petroleum products. We have detected a necessity of creation calculation methods based on reliable experimental data, providing greater accuracy, substantiated choice of directions for research SVP and density of petroleum products. Modern technology of petroleum processing and using of petroleum products requires the creation of more perfect installation for the study of SVP of substances and obtaining experimental data with greater accuracy. Generalized analytic dependence of SVP of petroleum products from all determining parameters have not yet been received. Therefore, experimental determination of this pressure should be the basis of the calculation of any device, because the calculations of petroleum products by the formulas and nomograms obtained with considerable error
-
ESTIMATION OF BEARING STRENGTH OF BRACES AND STRUTS OF FARMS OF COVERAGE OF 6D TYPE HOTHOUSES
DescriptionThe method of estimation of bearing strength of braces and struts of farms of coverage of hothouses is presented in the article. The deep analysis of the question of bearing strength appeared in the light of mass erection of hothouses, especially in the South Federal district, the construction of which had been bought in the countries of Near East. However, simple transfer of the constructions of hothouses made in foreign countries can not be considered as rational on the territory of the Russian Federation. The constructions of hothouses in most do not maintain exploitation even in one winter, when the considerable snow loadings are, and wind as well. The necessity of bringing of clarity for the folded situation became more obvious. Conducted successive static, dynamic and seismic analyses, executed upon the normative documents and due to the norms of supplier operating on the territory of the Russian Federation, in attachment to the real sections of bearings structural elements, allowed to expose the stated below percents of the use of the examined elements of constructions. Supporting braces of farms of coverage: on the norms of the Russian Federation, on the first maximum state percent of the use – 999 %; there is a percent of the use on the second maximum state – 999 %; on the norms of the Russian Federation taking into account loadings of supplier, on the first maximum state percent of the use – 999 %; there is a percent of the use on the second maximum state – 999 %; Stretched braces of farms of coverage: on the norms of the Russian Federation, on the first maximum state percent of the use – 64,2%; there is a percent of the use on the second maximum state – 721,8 %; on the norms of the Russian Federation taking into account loadings of supplier, on the first maximum state percent of the use – 25,8 %; there is a percent of the use on the second maximum state – 721,8%. Analysis presented allows establishing that at the load of supporting, stretched and central braces of farms of coverage of hothouses, by combinations of loadings characteristic for the place of location of hothouse of type of 6d, their bearing strength, and buildings can not be provided in general
-
Description
A method is considered, on the concrete example of hothouses of type of 6D, for calculation of bearing strength of overhead and lower belts of farms of coverage. The vital necessity of deep analysis of the question of bearing strength appeared in the light of satisfied mass erection of hothouses constructions of which are bought in the countries of Near East. However, a simple transfer of constructions of hothouses made in the countries of Near East can not be successful on the territory of the Russian Federation. These constructions of hothouses can not be maintained in some conditions, according to service exploitation, like snow loadings, in other cases - wind loadings, and in third case, a construction can collapse without visible reasons. The conducted successive static, dynamic and seismic analysis, executed due to the normative documents and the norms of supplier operating on the territory of the Russian Federation, in attachment to the real sections of bearings structural elements, allowed us expose the stated below percentage of the use of the examined elements of constructions. Lower belt of farms of coverage: on the norms of the Russian Federation, on the first maximum state percent of the use – 395 %; there is a percent of the use on the second maximum state – 999 %; on the norms of the Russian Federation taking into account loadings of supplier, on the first maximum state percent of the use – 339,3 %; there is a percent of the use on the second maximum state – 999 %. Overhead belt of farms of coverage: on the norms of the Russian Federation, on the first maximum state percent of the use – 495,2%; there is a percent of the use on the second maximum state – 361,4 %; on the norms of the Russian Federation taking into account loadings of supplier, on the first maximum state percent of the use – 150,8 %; there is a percent of the use on the second maximum state – 146,2%. Analysis presented allows establishing that at the load of overhead and lower belts of farms of coverage of hothouses, by combinations of loadings characteristic for the place of location of hothouse of type of 6d, their bearing strength, and buildings in general can not be provided
-
Description
A thermal physical and mathematical model of laser cladding with TiNi on steel was developed which allows us to monitor the formation of the structure and the properties of the surface layer. A description of the model included assumptions and simplifications; analysis of the energy balance; numerical modeling of thermal processes; evaluation of the temperature distribution; experimental verification of the obtained solutions. The composition of the steel and TiNi alloy was examined as a two-layer material with different thermal characteristics. The energy balance of the system was described with a heat equation in a three-dimensional form. The main channels of the radiation energy costs were taken into account: absorption surface of the product, loss owed to the reflection surface, energy absorbed by the coating which did not come down to the base material. To solve the differential equation of heat conduction we used the Fourier integral method. In assessing the temperature distribution we have reviewed a dimensional problem when exposed to a point source of the Gaussian distribution in a pulsed mode. Computer calculations used MathCAD graphs of temperature changes at different depths of the TiNi layer and the steel substrate. The results obtained allowed us to develop the recommendations for optimizing the technological parameters of laser cladding of TiNi. The simulation of thermal processes significantly reduces the time and resources required to develop the technology, allowing prediction of the quality of the surface layer during the development of the technology and promoting the adoption of efficient technical and technological solutions