05.00.00 Technical science
-
ANALYSIS AND SELECTION OF WORKING MACHINES FOR PRE-TREATMENT OF THE SOIL UNDER GRAIN CROPS
DescriptionThe best predecessors for sowing grain are grains and legumes, tilled cultures and perennial grasses. The precursor also determines the choice of the tillage type. The imperfection of the working bodies of the machines for soil treatment is the main reason for the increase in the complexity of preparing soil for sowing. In recent years, domestic manufacturers have been producing combined working machines that perform several technological operations in one pass. To prepare soil for sowing grain there have been selected disk units and working machines which were tested on the Kuban State Zonal Machine-Station. They fit well with the existing technology. It is rational to conduct tillage of soil for tall crops and perennial grasses by the disc cutter BDM-4×4. The disc cutter efficiently prepares the soil for seed bed cultivation on tilled precursors in one pass or two passes. It is efficient to conduct tillage on grain precursors by the stubble cultivator KSP-6, by the disc combined unit AKD-3 or DCN - 3.3. After grain predecessors the disc guns prepare soil for seed bed cultivation in two passes, and after perennial grass in a single pass. According to the results of the trials on the Kuban State Zonal Machine-Station the stubble cultivator KSP-6 efficiently prepares soil for sowing in one pass of the unit. The block-module cultivator MSC provides high quality pre-sowing cultivation simultaneously with sowing. There was proposed the method of equipping the unit so that it would provide usage of the data and technical characteristics of the tractor and physico-mechanical properties of the soil for which the technological operation is to be done. The proposed method determines the transmission ratio for which the amount of slipping does not exceed the permissible values in agro requirements. The value of the theoretical speed is calculated for the given transmission. Operating speed is determined taking into account the slip values
-
Description
The article presents analysis of emissions to the atmosphere in the regions of the North Caucasus Federal District by means of visualization tools of Tableau Public 9.0 in order to identify problem areas and to support management decisions
-
Description
The article has indicated the problem of the growth of document organization on the example of higher educational institution FGBOU "Kuban state technological University". Based on years of practice, the author conducted a detailed analysis of activity of service of documentary maintenance of management of the University and detailed analysis of the structure of the document taking into account the specifics of the direction of the organization. The article sets main tasks of service of the DOE, the actual problems of transition to paperless documentation of the organization's resources. We highlight problems of management and use of documents, due to the steady growth of documentary information. The major factors, influencing the growth of volumes of documents were given. Despite the rapid development of electronic document management in practice, electronic document duplicates the traditional paperwork. However, today the approach to document management is based on electronic technologies. The study of the author offers solutions to the general problem of reducing the volume of document workflow in the modern world
-
ANALYSIS OF DISK WORKING BODIES FOR MINIMUM TILLAGE
DescriptionMinimum tillage technology (mini till) is based on soil preparation for sowing by disk working organs. The spherical disc serves as a ploughshare and a blade and provides soil crumbling. There are two options for placement discs: a battery one on the X-axis with an individual bar. The working depth is adjusted by changing the angle of the battery attack. The distance between the tracks of the spherical discs on the common axis is 220 mm. In processing the soil with plant residues there is winding of stems on the axis which causes the disc jamming. The structural layout of the spherical disk on the individual axis with individual counter has none of these shortcomings. Spherical discs on the individual pole are placed on the frame in parallel rows. The working depth is adjusted by changing the angle of attack of each series. The number of rows on the harrow ranges from two to four. In the three-row harrow the front row is divided into two equal parts, with the working bodies being installed with the opposite direction of the bulge. The recommended working speed of the harrow is up to 12 km / h. The non-standard location of the disk of the mulcher on the spiral rack makes it possible to perform the following functions: crushing and incorporation of crop residues into soil, mulching. The number of rows of the mulcher is two or four, and the speed is of 15 - 18 km / h. The analysis of the data specifications of the harrows and mulchers with a different number of rows and different needs for the engine power of the tractor has been made. There has been determined the empirical dependence of the total number of disks upon the working width of the harrow and the mulcher. Dependence of the minimum power of the tractor upon the working width with different number of rows of the harrow and the mulcher was determined. It was found that at the same working widths, the double row harrow has the smallest value of the minimum power. At the fixed width, the double row mulcher has the highest value of the minimum power
-
ANALYSIS OF CIRCULAR INSTRUMENTS WITH FOUR IN-LINE ARRANGEMENT OF THE SPHERICAL DISKS
DescriptionThe main direction of reducing the cost of soil treatment based on resource-saving technologies is the transition to surface treatment of soil with disk tools. Double-row and four-row disc tools are manufactured. Four-row tools significantly increase tillage intensity. In the disk tools, the spherical disc is fixed on the individual pole. Disc headers are equipped with a rigid adjustment fixing the standalone pole to the frame. Recommended operating speed is up to 12 km/h. The advantage of a disc header over the disc harrow is as follows: winding plant residues on the axis are excluded. Disc mulchers are equipped with a spiral bar on which a spherical disk is mounted. The presence of the elastic element allows the working unit to do lowfrequency oscillations during movement. The result of processing is the formation of mulch in the layer of soil, which is a mixture of plant residues and soil particles with a diameter of up to 25 mm. To assess the effectiveness of the disc mulcher and the disc header a unit is composed. The initial data for calculation are as follows: tractor HTZ-150K, the resistivity of the soil is 6 kN/m, disk tool working width is 4 m, operating speed of the disc header is 12 km/h, operating speed of the disc mulcher is 15 km/h. Technical and economic performance of these units is defined during disking the soil. The choice of energy-saving operating regime was made in a well-known manner. Theoretical value of slippage of the leading tractor with disk mulcher was 6%, against 9% with the disc header. Working speed of the mulcher made up 14.07 km/h against 10,89 of the disc header. The performance of the unit with the mulcher made up 16.21 hectares, disc harrow performance is 12,54 ha. Fuel mass flow of mulcher decreased by 29% and made 9.68 kg/ha. Using mulcher for surface treatment of the soil allows to reduce the tillage energy costs thanks to resource-conserving technologies
-
Description
The influence of auto-displacement in a resonancetunnel diode (RTD) on the dynamic range of amplifiers on these diodes is considered in the article. The amplification at resonance frequency is considered and the influence of higher harmonics is not taken into account, since they do not create a significant voltage drop at the nonlinear resistance of the diode. It is assumed that the gain will be sufficiently large, and then the nature of the dependence of the gain factors on the degree of regeneration will be the same for amplifiers "per pass" and "reflection". This allows us to consider the problem for both types of amplifiers on the RTD. The types of amplitude characteristics , which are possible for the RTD amplifier, are considered. The dependences of the parameter determining the dynamic range of the amplifier on the position of the operating point for several values of the product of the resistance on the direct current of the supply circuit are calculated for the value of the modulus of the maximum negative conductivity of the tunnel gap RG max. For each value of RG max for given parameters, you can determine the position of the operating point, which provides the specified amplifier mode. Dependences of the value of the dynamic range are constructed with allowance for auto-displacement and in the absence of auto-displacement for two values of the degree of regeneration. Taking into account autosplacement, two possible types of amplitude characteristics and boundaries of their existence were revealed. For these two types of amplitude characteristics, expressions were obtained that determine the dynamic range of the amplifier
-
Description
The article is devoted to the analysis of the use of large data processing technology in information systems of territorially distributed complexes
-
Description
In the article, we have motivated the definition of the problem of increasing of efficiency of oil production with complicated conditions. We have also considered general system problems of increasing of the efficiency of oil production with the methods of the improvement and renovations of the equipment: the equipment for optimization of the factor of the extraction of oil; oil well rod pumping units and principles of energy saving on the late stage of the production of the bore holes with complicated condition of exploitation. It is shown, that the equipment allows optimizing the factor of the extraction of oil when developing hard extraction oil stocks, combined with modern technology and methods
-
Description
The existing settlement modes of loading of wheels of cars are defined for the conditions which are closest to road service conditions and are reflected in the existing standards. However these standards can't be applied to an assessment of functional qualities of systems of cushioning the cars which are operated in the conditions of agricultural production. The small step of roughnesses, change the cushioned characteristics under the influence of operational factors lead to emergence of the off-design modes of the movement. The purpose of the work was the research of loading of wheels of the car when moving on mulch of grains. For the purpose of obtaining characteristics of the roughnesses influencing car wheels we have recorded a smoothed microprofile of the field and got the statistics, rated autocorrelated function, spectral density of influence of a microprofile. For carrying out the researches the known mathematical model of a car road system was accepted. Influence of speed of the movement, normal rigidity of springs and tires, coefficients of damping of a suspension bracket and tires on vertical fluctuations and loading of wheels of forward and back axes of the car is investigated. The executed researches showed that the movement of the car is followed by fluctuations of indicators of loading of running system with obviously expressed periodic components. The change of the coefficient of damping of a passive suspension bracket and tires in possible limits has no essential impact on loading of wheels. Values of normal roughness of springs of forward and back axes of the car, normal rigidity of tires at which dynamic load of wheels of the car is minimum are established
-
Description
The possibility of reducing dynamic loads on the driving elements of hydraulic manipulator with a combination of motions of the three links is theoretically justified and confirmed by tests